November 2026

Antenna Tuners: Are We Fixing the Problem or Just Hiding It?


By Greg Lewis, N5XO
I have never been a particularly big fan of antenna tuners. Not because they don't work, but because I believe they are frequently used as a substitute for understanding, designing, and properly adjusting an antenna system.
Over the years, I have seen operators install antennas, discover they have a terrible SWR, connect an antenna tuner, press the tune button, and proudly announce that they now have a perfect 1:1 match.
Really? What exactly did you fix?
In many cases, absolutely nothing at the antenna itself!
You simply made the transmitter happy. Meanwhile, the antenna, transmission line, and whatever problems existed before you pressed that button are still there.
And that is my fundamental objection to the way antenna tuners are so often used in amateur radio.
What an Antenna Tuner Actually Does
First, let's understand the technology.
An antenna tuner, more accurately called an impedance matching network or transmatch, uses combinations of inductance and capacitance to transform the impedance presented by the antenna system into something the transmitter can comfortably operate into, typically 50 ohms.
That's it!
It does not physically change the antenna's length. It does not automatically make the antenna resonant. It does not repair poor connections, eliminate feed-line losses, improve an inadequate ground system, or magically increase radiation efficiency.
If your antenna presents a 5:1 SWR to your coaxial transmission line, placing a tuner at the transmitter and adjusting it to 1:1 does not eliminate that 5:1 SWR along the coax between the tuner and antenna.
The transmitter sees a good match. The transmission line still sees the original mismatch.
That is an extremely important distinction.
The Hidden Problem: Feed-Line Loss
Let's say you have an antenna with a significant impedance mismatch and 100 feet of coaxial cable between it and your transmitter.
That coax already has a certain amount of attenuation, even when perfectly matched.
Now introduce a substantial SWR.
The resulting standing waves produce additional losses in the transmission line. The severity depends on the cable's characteristics, operating frequency, length, and degree of mismatch.
When you install a tuner at the radio, those additional losses do not disappear.
You might have 100 watts leaving the transmitter, but substantially less reaching the antenna. Some of that missing energy becomes heat in the transmission line and matching network.
And remember,
the problem works in both directions.
On receive, signal energy is also lost in the feed line. A tuner cannot recover a weak signal that has already been attenuated by a lossy transmission line.
For those of us working weak-signal VHF, UHF, and microwave communications, these losses can be especially important.
When you're trying to pull a signal out of the noise on 144, 432, or 1296 MHz, every fraction of a decibel can matter.
Why spend substantial money on low-noise preamplifiers, high-gain antennas, and quality coaxial cable only to tolerate avoidable losses caused by a poorly matched antenna system?
A Perfect SWR Does Not Mean a Perfect Antenna
Here's another misconception that bothers me.
Some operators seem to believe that a 1:1 SWR automatically means an antenna is performing beautifully.
It doesn't!
A dummy load can provide an almost perfect 1:1 SWR, but you certainly wouldn't want to use one as your primary transmitting antenna.
A poorly constructed antenna with substantial resistive losses can also display an excellent SWR while converting far too much RF energy into heat rather than radiating it.
SWR tells us something important about impedance matching. It does not, by itself, tell us how efficiently an antenna radiates.
We need to understand the entire system, including antenna design, feed-point impedance, radiation resistance, loss resistance, feed-line attenuation, installation height, surrounding objects, and radiation pattern.
A low SWR is a measurement, not a certificate of antenna performance.
Resonance and Matching Are Not the Same Thing
Now, I want to make an important technical distinction.
An antenna does not necessarily have to be resonant to radiate efficiently.
Resonance means that the antenna's feed-point reactance is zero at a particular frequency. It does not automatically mean that the feed-point resistance is 50 ohms.
For example, a properly installed resonant half-wave dipole in free space has a feed-point resistance of approximately 73 ohms. Connected to 50-ohm coax, that represents an SWR of about 1.5:1.
Yet that antenna can be an excellent radiator.
Likewise, a nonresonant antenna can be very efficient when properly designed and matched.
This is where antenna tuners and matching networks have legitimate engineering applications.
A multiband doublet fed with low-loss balanced transmission line, for example, can work exceptionally well with a properly designed matching network.
A remote matching network installed directly at the antenna feed point can also be an excellent solution because it presents the proper impedance to the coaxial cable, reducing mismatch-related feed-line losses.
So my objection is not to impedance matching. My objection is to using a tuner to conceal problems that should have been corrected elsewhere.
Why I Prefer Fixing the Antenna
My approach has always been to start with the antenna system itself.
If I design an antenna for a particular operating frequency, I want to know what its feed-point impedance actually is, whether it is resonant where intended, what its SWR bandwidth looks like, and how the transmission line affects the measurements.
If something is wrong, I want to find out why.
Is the antenna too long or too short? Is the matching network incorrectly adjusted? Is the feed line damaged? Is water entering a connector? Is the antenna interacting with nearby metal objects? Is there unwanted common-mode current on the feed line?
These are engineering problems worth investigating.
Today, with affordable instruments such as the NanoVNA, there is very little excuse for not taking the time to understand what is happening.
We can measure impedance, resistance, reactance, SWR, and return loss. With appropriate calibration and measurement techniques, we can characterize the feed line and antenna system rather than blindly adjusting a tuner until a meter looks pretty.
And in the process, we become better amateur radio operators and technicians.
Are Antenna Tuners Ever the Right Answer?
Absolutely!
There are several legitimate reasons to use them.
An operator with limited space may need one antenna to cover multiple bands. A portable station may not have the luxury of installing an ideal antenna. A balanced-line-fed multiband antenna may be intentionally designed to operate with a matching network.
And sometimes a modest mismatch is perfectly acceptable, particularly with a short, low-loss feed line.
In these situations, a properly selected matching network can be an effective and efficient engineering solution.
There is also a big difference between a tuner located in the shack and one located at the antenna feed point.
The latter can correct the impedance mismatch before the RF enters a long coaxial transmission line.
But none of this changes my basic philosophy.
Use a tuner because the antenna system was designed to benefit from one, not because you don't want to investigate why the system isn't working properly.
My Bottom Line
I believe amateur radio should be about more than buying equipment, connecting cables, and pushing buttons until the indicators turn green.
We are supposed to be experimenting, learning, measuring, understanding, and improving our stations.
An antenna tuner is a useful tool, but it is not a magical repair device.
If you have a dedicated antenna operating on its intended frequency, particularly at VHF, UHF, or microwave frequencies, I would much rather see the antenna and its matching system properly adjusted than see an operator relying on a tuner in the shack to compensate for a significant mismatch.
That doesn't mean chasing an absolutely perfect 1:1 SWR. Sometimes 1.5:1 or even 2:1 is entirely acceptable, depending on the system.
It means understanding where your RF power is going and making intelligent engineering decisions.
My philosophy is simple:
Build the antenna correctly. Match it properly. Use quality transmission line. Measure the entire system. Correct problems at their source.
And if an antenna tuner is still necessary, use it with a clear understanding of what it accomplishes and what it cannot accomplish.
Because there is a tremendous difference between making your transmitter happy and making your antenna system perform efficiently.
73,
Greg Lewis — N5XO
HAMster Weak Signal Group
Amateur radio is about learning how things work, not simply making them work.

Taking Ham Shack Audio to a Whole New Level!


By Greg Lewis, N5XO
Cleaner Audio — Better Communications — More Enjoyable Operating!
One of the things I have always loved about Amateur Radio is that there is ALWAYS something new to learn, experiment with, improve, or simply have fun building. After decades in this hobby, I still get excited about a new project, especially one that can make a real difference in how I enjoy operating.
My latest adventure is a complete
Ham Shack Audio Enhancement System, and I am REALLY excited about the possibilities!
So, What Am I Building?
114E83EB-5768-4BDA-8EF6-85DB8F154D35_1_105_c
My shack has multiple radios covering HF, VHF, UHF, and SHF, with a particular emphasis on weak-signal SSB and CW operations. I've always wanted a way to bring the receive audio from my various radios together, improve the sound quality, reduce listening fatigue, and have much greater control over what I hear.
At the heart of this project is a
Yamnweo MD-14 digital audio mixer, along with a Behringer Ultragain Pro microphone preamplifier, two dbx 231s graphic equalizers, quality microphones, Klipsch studio speakers, and my Mac computer.
The idea is to route audio from several radios through one central system, giving me individual control over audio levels, equalization, filtering, and routing.
Imagine monitoring several bands simultaneously, adjusting each receiver independently, and listening through a good pair of studio monitors instead of several small communications speakers scattered around the shack!
THAT is something I am looking forward to!
Why All the Excitement?
For me, the biggest benefit is improving the actual operating experience.
Anyone who has spent hours listening for weak VHF/UHF signals knows how tiring receiver hiss, background noise, and harsh audio can become.
With this system, I will be able to experiment with equalization, audio processing, and filtering to emphasize the frequencies that make speech easier to understand. While no audio processor can magically recover a signal buried below the noise, proper adjustment can make marginal signals more intelligible and long operating sessions considerably more comfortable.
There are several benefits I'm particularly excited about:
  • Better receive audio: Individually adjust the tone, levels, and filtering of each radio.
  • Improved weak-signal listening: Experiment with audio settings optimized for SSB, CW, and different operating conditions.
  • Better transmitted audio: Use quality microphones, proper equalization, and level control to produce clear, natural-sounding transmissions without excessive processing.
  • Multiple-radio monitoring: Listen to several receivers through one centralized audio system.
  • Recording contacts: Digitally record and archive rare DX contacts, band openings, contests, nets, and special events.
  • Custom audio setups: Develop different settings for SSB, FM, CW, and general monitoring.
And one of my favorite features will be the ability to record those rare contacts that happen unexpectedly. How many times have we made an extraordinary contact during a band opening and wished afterward that we had recorded it?
Now I intend to have that capability readily available!
But I'm Going a Step Further!
My particular installation is considerably more elaborate because I have another goal in mind.
I want the shack equipped for LIVE AUDIO AND VIDEO STREAMING!
Eventually, I want to be able to stream activity directly from the shack, including operating sessions, band openings, contests, demonstrations, technical training, and perhaps even some live HAMster activities.
The audio mixer will become an important part of that capability, allowing me to select and control which radio audio, microphones, and computer audio are included in a live broadcast.
It also opens up some interesting possibilities for remote participation, recording training sessions, and sharing the excitement of weak-signal Amateur Radio with others.
This is particularly exciting as we continue developing our ACCENT BBS system and expanding what we can offer our fellow HAMsters.
NOW, HERE IS SOMETHING IMPORTANT!
YOU ABSOLUTELY DO NOT HAVE TO BUILD ANYTHING THIS ELABORATE!
I want to emphasize that point because I don't want anyone looking at the equipment and thinking this is what it takes to improve their shack audio.
IT DOESN'T!
You can make meaningful improvements with a simple audio equalizer, a small inexpensive mixer, better speakers, or even a good pair of headphones.
A modest setup involving one radio, a basic equalizer, and an external speaker can make a noticeable difference in listening comfort and intelligibility.
My system is more complicated because I am combining several goals into one project: multiple radios, transmit and receive audio processing, digital recording, computer integration, and eventually live audio-video streaming.
Start simple, experiment, learn, and expand as your interests grow!
The Real Reason I Love Projects Like This
Amateur Radio has never been just about buying equipment and getting on the air for me.
It's about experimenting, understanding how things work, finding ways to improve them, and sharing what we learn with others.
Will I get everything adjusted perfectly the first time?
ABSOLUTELY NOT! I'm sure there will be some head-scratching, rewiring, experimenting, and probably a few colorful words along the way!
But that's half the fun!
I'm looking forward to getting this system fully integrated, experimenting with different audio configurations, and sharing the results, including what works, what doesn't, and what I would do differently.
And perhaps most importantly, I hope it encourages a few other operators to experiment with improving their own shack audio.
Because sometimes the most enjoyable improvements in Amateur Radio aren't about transmitting more power or putting up another antenna. Sometimes they're simply about hearing what you've been missing!
73,
Greg — N5XO HAMster Weak Signal Group Experimenting, Learning, and Having FUN with Amateur Radio!